ENGINEERED FOR THE FACILITIES THAT CAN'T AFFORD TO STOP
Grinding, polishing and cutting metal put airborne particles, fumes and gases into the shop. Many of them carry metal oxide compounds that reach the lungs and cause serious long term illness. There is a property risk alongside the health one, because where dust collection is inadequate a welding spark can start a fire or an explosion in material that has been allowed to collect.
The complication in metalworking is that the contaminants do not match each other. Dry grinding dust, welding fume and oil aerosol behave differently in a duct and respond to different filter media. A metal dust collection system that treats them as one load either overspecifies for two of them or fails on the third.
Coral USA specifies per station rather than per building. Extraction arms, portable units and downdraft tables handle capture at the source. Stationary cartridge and sleeve systems carry the centralized duty. Oil mist collectors take the aerosol load that dry media cannot hold.
Products
Heavy-duty self-supporting arm for full-shift source capture of welding smoke, oil fumes, and dust at a single workstation.
Extraction arm with its own fan and cartridge filter built in, so one workstation gets source capture without any ductwork.
Grounded, static-dissipating arm with 316 stainless piping, built for capture points that sit inside classified explosive atmospheres.
Light-duty welding arm, flexible along its full length, for intermittent bench work on cart units or central systems.
Self-contained portable welding fume extractor that runs on standard 120-volt single-phase power, ready for light-duty work anywhere.
Portable self-cleaning cartridge extractor, shipped with one or two Evolution arms, moving up to 1,345 CFM for welding stations.
Self-cleaning grinding extractor with a stainless wet pre-chamber and spark trap that quenches sparks before the cartridges.
Mobile collector with a built-in suction worktop, so small parts are welded or ground and captured on the same surface.
Iperjet base model with four, six, or nine horizontal cartridges, handling welding fume and dust without a central plant.
Iperjet built for heavy duty, stepping up to 9, 12, 18 or 24 horizontal cartridges to move more air across larger applications.
Air purification tower for full-room filtration of welding and cutting fumes where local source capture is not practical.
Plug-and-play collector for plasma, laser, and oxygen cutting tables, with a mesh pre-chamber that traps glowing particles before the filters.
Centralized sleeve collector handling wood chips and metalworking dust, with row-by-row reverse jet cleaning that never interrupts airflow.
Vertical cartridge collector in galvanized panels, with cartridges matched to your process for continuous medium and fine dust loads.
Wet collector that scrubs air with water instead of media, the choice for combustible metal fines from sanders and grinders.
Airborne particles from grinding, polishing and cutting carry metal oxide compounds that reach deep into the lung and cause long term illness. Oil mist and oil smoke add a second exposure and a second failure mode, because the same aerosol settles inside machine electronics and produces sudden failures that read as machine faults rather than air quality ones.
Filtering the airborne fraction is therefore not optional housekeeping. It is what keeps a fabrication floor operating, and it is the difference between an accumulation that gets swept and one that ignites.
Extraction arms, portable extraction units and downdraft tables remove fume and smoke directly at the source, which is the only place capture efficiency is cheap. The Grindex DF JET adds a wet pre-chamber and spark trap for dry grinding, where live sparks would otherwise reach the cartridges.
Centralized collection and filtration systems handle the higher loads, and because the stationary units are modular they can be extended as the shop changes rather than replaced. For oil mist, the Noil mounts directly on the machine tool and Oil STOP serves multiple machines from one centralized system, both recovering oil for reuse.
FAQ
Put the spark trap ahead of the media. The Grindex DF JET carries a stainless steel wet pre-chamber tray at the inlet that extinguishes live sparks, removing the fire path that incandescent particles otherwise carry into a cartridge.
Where collection is inadequate, accumulated dust plus a welding spark is a fire or an explosion. That is the property risk sitting alongside the health one, and it is why filtering the airborne fraction is not housekeeping but what keeps a fabrication floor operating.
At the source wherever the process allows it. Extraction arms, portable units and downdraft tables capture at the point of generation, and room level treatment costs several times the airflow for the same result in the breathing zone.