ENGINEERED FOR THE FACILITIES THAT CAN'T AFFORD TO STOP
Building aerospace parts runs through a sequence of processes that release metallic dust and welding fume, and composite work adds its own fine particulate at every trim, sand and finish operation. Both loads reach your people and your parts. Carbon fiber dust collection and metallic fume control therefore have to be designed around the processes actually on your floor, not added afterwards as a single collector in a corner.
Coral has built extraction and filtration equipment since 1958, and Coral USA has supplied aerospace plants for more than 40 years. That history matters here because aerospace cleanliness requirements are not a fabrication shop’s requirements. A system that meets the airflow number but sheds fiber, or recirculates without a final filter stage, fails an audit it was never specified to pass.
The practical answer is capture at the tool. Composite trim, sanding and finishing get downdraft or arm capture at the bench. Weld and thermal cutting stations get source capture rated for the metal being cut. Larger cells feed a modular stationary unit with automated pneumatic cleaning, so the filtering surface holds its efficiency through a full production shift instead of degrading between manual cleans.
Products
Heavy-duty self-supporting arm for full-shift source capture of welding smoke, oil fumes, and dust at a single workstation.
Extraction arm with its own fan and cartridge filter built in, so one workstation gets source capture without any ductwork.
Grounded, static-dissipating arm with 316 stainless piping, built for capture points that sit inside classified explosive atmospheres.
Light-duty welding arm, flexible along its full length, for intermittent bench work on cart units or central systems.
Self-contained portable welding fume extractor that runs on standard 120-volt single-phase power, ready for light-duty work anywhere.
Portable self-cleaning cartridge extractor, shipped with one or two Evolution arms, moving up to 1,345 CFM for welding stations.
Self-cleaning grinding extractor with a stainless wet pre-chamber and spark trap that quenches sparks before the cartridges.
Iperjet base model with four, six, or nine horizontal cartridges, handling welding fume and dust without a central plant.
Iperjet built for heavy duty, stepping up to 9, 12, 18 or 24 horizontal cartridges to move more air across larger applications.
Air purification tower for full-room filtration of welding and cutting fumes where local source capture is not practical.
Centralized sleeve collector handling wood chips and metalworking dust, with row-by-row reverse jet cleaning that never interrupts airflow.
Vertical cartridge collector in galvanized panels, with cartridges matched to your process for continuous medium and fine dust loads.
Downdraft work table with cartridge filters, pulling grinding and sanding dust down through the slotted top away from the operator.
Metallic dust and welding fume carry toxic particles that cause acute health effects on inhalation, and the exposure accumulates rather than announcing itself on the day. That is why most aerospace plants specify control after a monitoring result rather than before one.
The second problem is fire. Aluminum, titanium and magnesium dust are highly explosive once a quantity has accumulated, and the accumulation is the part that happens quietly. The third is product quality: uncontrolled particulate reaching electronic components, bond lines or paint-critical surfaces turns an air quality issue into scrapped parts.
For local capture directly at the source, Coral USA supplies portable extraction units, downdraft tables and flexible extraction arms that hold position through a shift. On composite work the capture point belongs at the trim or sand operation, not at the room.
Where the load is heavy or the footprint is tight, modular stationary units carry the duty. Automated pneumatic cleaning keeps the filtering surface at its working efficiency instead of drifting between services, and the modularity means a cell added next year does not mean replacing the collector.
FAQ
Carbon fiber particulate is electrically conductive and extremely fine, so it does two things ordinary metal dust does not: it stays airborne far longer, and it shorts electronics it settles inside. A collector specified for aluminum swarf passes the fraction that matters here, which is why the media and the final filter stage are chosen for the composite rather than for the airframe metal.
Yes. Aluminum, titanium and magnesium dust are all highly explosive once a quantity has accumulated, and accumulation is the part that happens quietly between shifts. Collection sized to stop the accumulation forming is the control. Housekeeping on its own is not.
Rarely well. The two loads differ in particle size, conductivity and ignition behavior, and combining aluminum or titanium dust with combustible composite dust in one collector creates a hazard neither presents alone. Coral USA specifies separate capture per process, feeding modular stationary units sized to each.
Directly. Uncontrolled particulate reaching electronic components, bond lines or paint-critical surfaces produces rework and scrap, so the system that keeps monitoring results inside limits is also protecting first pass yield.