ENGINEERED FOR THE FACILITIES THAT CAN'T AFFORD TO STOP
Every welding process gives off visible smoke carrying metal fume and gases. The particles in that smoke measure less than a micrometer across, small enough to be inhaled deep into the lung and absorbed into the body. Thermal cutting adds to the load, because melting metal releases the same airborne fume from a torch or plasma head that never stops moving.
A welding fume extraction system is specified around three things: how much of the shift the arc is actually burning, how far the capture point can sit from it, and whether the station stays where it is. Get those right and a modest unit outperforms a large one placed badly. Get them wrong and airflow that looks correct on paper never reaches the breathing zone.
Coral USA builds for both ends of that range. Portable extractors cover intermittent duty and rotating stations on standard single phase power. Centralized cartridge and sleeve systems carry continuous production, with extraction arms that hold their position all day and pressure losses low enough that the fan is not compensating for the ductwork.
Products
Heavy-duty self-supporting arm for full-shift source capture of welding smoke, oil fumes, and dust at a single workstation.
Extraction arm with its own fan and cartridge filter built in, so one workstation gets source capture without any ductwork.
Grounded, static-dissipating arm with 316 stainless piping, built for capture points that sit inside classified explosive atmospheres.
Light-duty welding arm, flexible along its full length, for intermittent bench work on cart units or central systems.
Self-contained portable welding fume extractor that runs on standard 120-volt single-phase power, ready for light-duty work anywhere.
Portable self-cleaning cartridge extractor, shipped with one or two Evolution arms, moving up to 1,345 CFM for welding stations.
Self-cleaning grinding extractor with a stainless wet pre-chamber and spark trap that quenches sparks before the cartridges.
Mobile collector with a built-in suction worktop, so small parts are welded or ground and captured on the same surface.
Iperjet base model with four, six, or nine horizontal cartridges, handling welding fume and dust without a central plant.
Iperjet built for heavy duty, stepping up to 9, 12, 18 or 24 horizontal cartridges to move more air across larger applications.
Air purification tower for full-room filtration of welding and cutting fumes where local source capture is not practical.
Plug-and-play collector for plasma, laser, and oxygen cutting tables, with a mesh pre-chamber that traps glowing particles before the filters.
Vertical cartridge collector in galvanized panels, with cartridges matched to your process for continuous medium and fine dust loads.
Without capture in place, metal particles reach every person working in the area rather than the welder alone. Prolonged exposure is associated with cancer and with nervous system and kidney damage, and where ventilation is inadequate certain shielding and process gases carry a suffocation risk of their own.
The cost lands elsewhere too. Fume that is not captured settles on the shop, on stock and inside equipment, and an OSHA or EPA finding on a monitoring result is more expensive than the system that would have prevented it.
For intermittent operation, small portable welding fume extractors and collectors move between stations and run on standard power. For medium to high airflow, centralized collection and filtration systems use cartridge, sleeve or bag filters sized to the duty.
Alongside those, self supporting extraction arms and downdraft tables with filtration put the capture point where the fume is generated. Thermal cutting adds one further requirement, and the Aircompact TC answers it with a metal mesh pre-separator that stops incandescent particles before they reach the filtering elements.
FAQ
Start with three numbers: how much of the shift the arc is actually burning, how far the capture point can sit from it, and whether the station stays where it is. A modest unit placed at the arc outperforms a large one placed badly, because airflow that looks correct on paper never reaches the breathing zone if the hood cannot get close.
Portable units cover intermittent duty and rotating stations, and one Cleango or Jetclean DF can serve several bays across a shift. Continuous production on fixed stations is where a centralized cartridge or sleeve system pays back, because the fan, the filter area and the cleaning cycle are all sized for a full shift rather than a burst.
Yes. Plasma, laser and oxy fuel cutting throw incandescent particles that reach filter media still glowing. The Aircompact TC answers that with a metal mesh pre-separator at the inlet, and it is the reason a standard collector should not be put on a cutting table.
Metal particles in welding smoke measure less than a micrometer across, small enough to be inhaled deep into the lung and absorbed into the body. Prolonged exposure is associated with cancer and with nervous system and kidney damage, and inadequate ventilation adds a suffocation risk from certain shielding and process gases.
It is what makes compliance demonstrable. Source capture keeps the breathing zone inside limits instead of relying on dilution across the building, and a monitoring finding costs considerably more than the system that would have prevented it.